...and as expected, this turns up quite some inconsistencies,
especially regarding usage of the »buffer types«.
Basically, the `PortBuilder` is responsible for the high-level functionality
and thus must ensure the nested `WiringBuilder` is addressed and parameterised
properly to connect all »slots« of the processing function.
- can use a helper function in the WiringBuilder to fill in connections
- but the actual buffer types passed over these connectinos are totally
unchecked at that level, and can not see yet how this danger can be
mitigated one level above, where the PortBuilder is used.
- it is still unclear what a »buffer type« actually means; it could
be the pointer type, but it could also imply a class or struct type
to be emplaced into the buffer, which is a special extension to the
`BufferProvider` protocol, yet seems to be used here rather to transport
specific data types required by the actual media handling library (e.g. FFmpeg)
__Analysis__: what kind of verifications are sensible to employ
to cover building, wiring and invocation of render nodes?
Notably, a test should cover requirements and observable functionality,
while ''avoiding direct hard coupling to implementation internals...''
__Draft__: the most simple node builder invocation conceivable...
* decision how to provide a default service for tests
while also allow for configuration of more specific services
* as starting point for the prototype: use the `TrackingHeapBlockProvider`
(simply because this is the only implementation available and tested)
...need to pass a binding for the actual processing function
in a way that it acts as a ''prototype'' — since the `Feed`,
i.e. the ''Invocation Adapter'' must be generated for each
invocation anew within the current stack frame
(so to avoid spurious heap allocations)
...seems that the former is well suited to serve as detail builder
used internally by the latter to provide a simplified standard adaptation
for a given processing function.
The integration can be achieved to layer a specialised detail builder class
on top, which can be entered only by specifying the concrete function or lambda
to wrap for the processing; the further builder-API-functions to control
the wiring in detail become thus only accessible after the function type
is known; this allows to place the detail builder as member into the
enclosing port builder and thus to allocate everything within the current
stack frame invoking the builder chain.
...by relying on DI for some effectively global services, notably
the cache provider, the API for building and wiring render nodes
can be simplified to cover only the actual node connectivity
Doing so directly seems to be a better solution than to inject an OutputBufferProvider;
the latter will still be needed, yet will not be part of the regular weaving pattern,
but used directly at top-level to obtain the output `BuffHandle`, which is then
passed to the `Port::weave()` call
...still not convinced that this is a good design,
since it seems to subvert the general design to treat one special case.
However, I can't see a good way to address this special case directly
Requirement analysis shows that the ''actual buffer provider'' to use
constitutes yet another independent degree of freedom, which conceivably
must be handled by the Builder internals rather than by the Domain Ontology.
Thus the simple solution to use a `BuffDescr` to mark the type must be augmented
to also allow configuration of the underlying `BufferProvider`, which generates
the descriptor and can later be invoked with this descriptor to ''lock an actual Buffer.''
In some cases, setup of the buffer types could even be more complicated and require
access to the actual (runtime) invocaton context; such extreme cases however
could be rendered as an extension of the scheme established here,
by storing the (up to now transient) constructor functors persistently.
Which leads to the decision not to care for those extremely complicated
corner cases right now, and thus to construct all buffer descriptors
in the `build()` call
...still fighting to find a suitable API to define
how inputs and outputs are connected and mapped to function parameters.
The solution drafted here uses the reshaped `DataBuilder` (≙`lib::SeveralBuilder`)
to add up connections for each »slot«, disregarding the possibility of permutations.
Similar to `NodeBuilder`, a policy template is used to pass down the setup
for an actual custom allocator.
